It can be interfaced to a PC containing the software required to update the ECU diagnostics software through one of the following lines :

>> standard RS232C serial line
>> USB serial line
>> Ethernet 10/100Mbit network
>> Ethernet Wireless 802.11b network

For better efficiency and faster data transfer between the PC and the SD3 unit, we suggest you use the USB line or an Ethernet/Wireless network for communications.

The System IS Supplied the SD3 the Diagnostic of The A with Suitcase containing:

Tester at The SD3 >>;
>> Serial Cable for at The SD3 / SD2 are at The Connection to PC (at The SD3-CBL01) [095 970 327];
>> Cable Multimeter (at The SD3-CBL02) [095 970 328];
>> Power supply feeder (SD3-CBL05) [095970331];
>> EOBD SD3 diagnosis cable (SD3-CBL06) [095970332];
>> Diagnosis cable with SD2 bridle (SD3-CBL07) [095970333];
>> Connection cable for feeding Among SD2 and SD3 bridle (SD3-CBL08) [095970334];
>> Cigar lighter socket feeder (SD3-CBL09) [095970335];
>> ISO 1 extension (SD3 -CBL10) [095970336];
>> ISO 2 extension (SD3-CBL11) [095970337];
>>SD2 B-CAN adapter (SD3-CBL12);
>> USB cable [095970330];
>>10/100 Mbps Ethernet cross-over cable [095970329];
>> SD3 wireless board; SD3 Manual [095970324];
>> SD3 Quick Reference;
>> Installation CD-ROM [095970326];
>> 8 metal-point rods For Multimeter.
>> PC USB/Wireless board

To install the Basic SD3NET software on the PC, proceed as follows:

1. Power the the PC where the program has to be installed;
2. Insert the program CD supplied with the SD3 in the CD drive.
3. If the user has enabled The AUTORUN function on the CD drive, the installation wizard will launch automatically ; in this case go to point 7, otherwise continue the procedure below;
4. Using your mouse, double-click on MY COMPUTER;
5. When the computer resources window opens Double-click on the CD icon where the SD3NET program has been inserted ;
6. The window of The Double-A website Opens the Showing of The Clicking the Contents of the CD of The Double the ON The The The the SETUP.EXE the Installation of the Click of The Wizard Will now the RUN; ..
7. The window of The displayed for the BE A of The Will of The Language of The Selection of During Program Installing to use.
8. The installation wizard displays a start window. Click on NEXT to continue;
9. You will be prompted to install Microsoft Framework NET 1.1 (if It is not present). Always confirm and proceed with installation;
10. You are asked to name The directory in which the program will be installed (we recommend leaving the default setting). Click on NEXT to continue ;
11. You are asked to The Directory in Which the DATA name The Program Will BE Installed (WE Recommend Leaving Setting The default) Continue to the Click the NEXT ON;.
. 12. The window of The Last Gives A Summary of The Previous Selections The Press and the NEXT COPYING The Program System Soho starts to your PC.
13. When the installation has terminated you will be asked to reboot your PC. This is essential for the program to operate correctly;
14. When the PC has been rebooted, the SD3NET? icon will appear on the desktop.

Multimeter

The SD3 Diagnostics System has an integrated multimeter that can take measurements in Volts (up to 200 V dc) and Ohms (up to 1 Mohm). This function can be selected from the SD3 Tester main menu.

Scantool OBD

The SD3 Diagnostics System has an integrated Standard Scantool OBD software. This system makes it possible to automatically check for systems able to support the service (engine, shift, ...). Once the control unit has been identified by the software, you can Check some parameters/errors supplied by the system itself.

This function can be selected from the SD3 Tester main menu.

Power supply voltage

The SD3 requires a voltage between 8 and 16 V DC which is supplied either by the battery of the vehicle being tested or by the power supply provided with the product.

Installation instructions for the SD3

The SD3 does not require any installation; it only needs to be configured with the diagnostics software to be used. The downloaded software are stored in the non-volatile memory of the SD3 unit. The SD3 is equipped with a battery-powered clock which can Be set and checked on the PC through a special software menu.

General Description

The figures are provided a diagram of the upper part (containing the power supply and diagnostics connectors), the front part of the SD3 unit (containing the display, keypad and ON light) and the lower part (containing a flap which provides access to the lower part Part Part Part Used to hook up an American PS2 keyboard for the PC, and two PCMCIA connectors used for any hardware expansions-eg flash expansions, Wireless card-through external boxes).

The ten keys at the bottom of the screen are used to input data (numbers/letters) into the diagnostics software.

The directional arrows and the TAB key feature function repetition if the key is held down continuously.

In all menus, hold down "Switch" and "Esc" for 4 seconds to reset the SD3 Tester software. This speeds up restarting the device if the software crashes (the Tester does not respond to the keywords commands).

The top holds the following:

· The power button.

· One 25-pin connector for power and serial diagnostics lines (on the power button side);

· One 9-pin connector (male) for hook up to the PC (in the centre);

· One 9-pin connector (female) for Multimeter inlet.

· One Ethernet 10/100 Mbit connector.

· One USB connector.

· One Connector to hook up a CRT VGA monitor

Self test

To quickly check that the device is functional, connect the power supply (for example, with the cord

And the mains power supply), press the power button and check that the led lights up. Within 20/30 seconds

The start icon appears on the display.

The SD3 has a resettable fuse. If it is activated because of an internal fault or due to the external cabling,

Wait a few minutes to allow it to reset. If, when you switch on the SD3, the display does not light up, wait a

Few minutes and repeat the procedure.